[lubuntu] wireless network card problem

hi guys i have wanna change my wirelss network care to monitor mode
but when i type

Code:

sudo iwconfig wlan0  mode monitor

thats what i got

Code:

Error for wireless request "Set Mode" (8B06) :    SET failed on device wlan0 ; No such device.

when i type

Code:

ifconfig

that is the resulat below

Code:

enp7s0    Link encap:Ethernet  HWaddr 20:47:47:00:79:6e            UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


enx001e101f0000 Link encap:Ethernet  HWaddr 00:1e:10:1f:00:00  
          inet addr:192.168.8.100  Bcast:192.168.8.255  Mask:255.255.255.0
          inet6 addr: fe80::21e:10ff:fe1f:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:27389 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21947 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:25984015 (25.9 MB)  TX bytes:2665614 (2.6 MB)


lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:3778 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3778 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:447777 (447.7 KB)  TX bytes:447777 (447.7 KB)

the result of

Code:

lshw -c network

is :

Code:

WARNING: you should run this program as super-user.  *-network DISABLED      
       description: Wireless interface
       product: BCM43142 802.11b/g/n
       vendor: Broadcom Corporation
       physical id: 0
       bus info: pci@0000:06:00.0
       logical name: wlp6s0
       version: 01
       serial: ac:d1:b8:c7:b2:ef
       width: 64 bits
       clock: 33MHz
       capabilities: cap_list ethernet physical wireless
       configuration: broadcast=yes driver=wl0 driverversion=6.30.223.248 (r487574) latency=0 multicast=yes wireless=IEEE 802.11abg
       resources: irq:18 memory:f7200000-f7207fff
  *-network
       description: Ethernet interface
       product: RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:07:00.0
       logical name: enp7s0
       version: 07
       serial: 20:47:47:00:79:6e
       size: 10Mbit/s
       capacity: 100Mbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8106e-1_0.0.1 06/29/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s
       resources: irq:47 ioport:e000(size=256) memory:f7100000-f7100fff memory:f2100000-f2103fff
  *-network
       description: Ethernet interface
       physical id: 2
       logical name: enx001e101f0000
       serial: 00:1e:10:1f:00:00
       capabilities: ethernet physical
       configuration: broadcast=yes driver=cdc_ether driverversion=22-Aug-2005 firmware=CDC Ethernet Device ip=192.168.8.100 link=yes multicast=yes
WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

plz help me guys and sorry for my bad language i don't speak english very well

Let's block ads! (Why?)

[lubuntu] wireless network card problem